The Chimney Sweep Woodstoves, Gas Stoves, Fireplaces, Cookstoves and Barbecues
The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop

CLEARANCES TO COMBUSTIBLE WALLS

STOVE MODEL: HEARTHSTONE TRIBUTE WOODSTOVE
STOVE DIMENSIONS: 22" WIDE X 18" DEEP X 25 1/4" TALL
CONNECTOR PIPE USED: 6" SINGLE-WALL OR DOUBLE-WALL STOVEPIPE
MINIMUM HEARTH (FLOOR PROTECTION) REQUIREMENTS:
ANY SOLID, NON-COMBUSTIBLE MATERIAL WITH AN R-VALUE RATING OF AT LEAST 0.6
(CLICK HERE FOR R-VALUE CHART)
MINIMUM HEARTH EXTENSION FROM SIDES AND REAR OF STOVE... 3-1/2"
MINIMUM HEARTH EXTENSION FROM LOADING DOOR OF STOVE........ 16"


FLAT WALL INSTALLATIONS:


CORNER INSTALLATIONS:

A: STOVE TO BACKWALL:
NO SHIELD, SINGLE-WALL STOVEPIPE......... 19"
REAR SHIELD & DOUBLE-WALL PIPE............. 8" 		G: STOVE TO CORNER WALLS:
NO SHIELD, SINGLE-WALL STOVEPIPE... 17"
REAR SHIELD & DOUBLE-WALL PIPE....... 7"
B: STOVE TO SIDEWALL:
NO SHIELD, SINGLE-WALL STOVEPIPE... 16-1/2"
REAR SHIELD & DOUBLE-WALL PIPE..... 16-1/2" 		H: CENTERLINE PIPE TO CORNER WALLS:
NO SHIELD, SINGLE-WALL STOVEPIPE... 29"
REAR SHIELD & DOUBLE-WALL PIPE..... 19"
C: CENTERLINE PIPE TO BACKWALL:
NO SHIELD, SINGLE-WALL STOVEPIPE......... 24"
REAR SHIELD & DOUBLE-WALL PIPE........... 13" 		I: DIAGONAL CORNER TO FRONT LOP:
NO SHIELD, SINGLE-WALL STOVEPIPE... 69"
REAR SHIELD & DOUBLE-WALL PIPE..... 54"
D: CENTERLINE PIPE TO SIDEWALL:
NO SHIELD, SINGLE-WALL STOVEPIPE... 27-1/2"
REAR SHIELD & DOUBLE-WALL PIPE..... 27-1/2" 		J: CORNER TO EDGE OF HEARTH:
NO SHIELD, SINGLE-WALL STOVEPIPE... 60"
REAR SHIELD & DOUBLE-WALL PIPE..... 50"
E: MINIMUM HEARTH WIDTH........................ 29" L: WIDTH OF FRONT LOP......................... 29"
F: BACKWALL TO FRONT OF HEARTH:
NO SHIELD, SINGLE-WALL STOVEPIPE......... 53"
REAR SHIELD & DOUBLE-WALL PIPE........... 42" 		COMBUSTIBLE ALCOVE DIMENSIONS:
MINIMUM 55" WIDE X 51" TALL
MAXIMUM 25" DEEP

Setting up the Tribute to burn air from outside the house

OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACE
Bolt optional outside air adapter to Tribute at bottom rear. Attach a length of 3" rigid or flexible aluminum pipe to the intake collar with a 3" pipe clamp, then elbow down through a 3-1/8" hole in the floor behind the stove, extending the pipe below the floor joists and insulation. Caulk around the pipe where it penetrates the floor and use silicone cement to glue on a piece of 1/4" wire rodent mesh at the bottom.
OUTSIDE AIR SUPPLIED THROUGH BACKWALL
Bolt optional outside air adapter to Tribute at bottom rear. Attach a length of 3" rigid or flexible aluminum intake pipe to the intake collar with a 3" pipe clamp, extend through a 3-1/8" hole in the outside wall behind the stove. Attach a standard 3" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place.


Click to View or Download the installation manual in .pdf format

To return to the Tribute page, click here. For other options, click a button below.

Wood Stoves    back to our home page  Index by manufacturer

The Chimney Sweep, Inc.
913 Harris Avenue
Bellingham, WA 98225-7032
1(888)-354-6722 toll-free in U.S. & Canada
1(360)-676-9080 FAX
http://www.chimneysweeponline.com

To send us E-Mail, Click Standard E-Mail Window or contact us (our reply form)
Copyright © 1996 - 2013 The Chimney Sweep, Inc.