The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
FIREPLACE MODEL: MENDOTA DXV-35 DEEP TIMBER II GAS FIREPLACE
The DXV-35 has vent collars on both top and rear, and may be vented straight back, straight up, or up and out.
DIAGRAM #1: FRAMING THE ENCLOSURE
A: Opening Height, Floor to Header (minimum).................. 31 1/2"
B: Opening Width (minimum)............................................. 37 1/8"
C: Opening Depth (minimum)............................................. 16 1/8"
D: Floor to Bottom of Enclosure Ceiling (if rear vented)...... 40 1/2"
D (1): If Direct Vented Up-And-Out, NG installations........ 49-1/2"
D (2): If Direct Vented Up-And-Out, LP installations......... 52-1/4"
E: Floor to Centerline Exhaust Opening (see drawing below)
The LP Top Direct Vent Kit is taller than the Natural Gas Kit
F: Floor to 8" Combustible Mantel (minimum)........................... 43"
G: Edge of Opening to Combustible Sidewall (minimum)........... 10"
H: Hearth (floor protection) Extension in Front of Opening........ 12"
H(1): Thickness of Non-Combustible Hearth Material.............. 1/4"
I:. Hearth (floor protection) Minimum Width............................. 36"
DIAGRAM #2: FIREPLACE DIMENSIONS
J: Floor to Top of Header Standoffs.................................... 31 1/2"
K: Front Height, Excluding Header Standoffs............................. 29"
L: Front Width.......................................................................... 36"
M: Rear Width.................................................................... 22 1/4"
N: Fireplace Depth.............................................................. 15 1/2"
O: Faceplate Height (inside the 2" top & bottom borders).......... 25"
O*: Faceplate Height, Andover, Bentley & Prairie Models: 29 5/16"
P: Faceplate Width (inside the 2" left & right side borders)......... 32"
P*: Faceplate Width, Andover, Bentley & Prairie Models.... 36 3/4"
Q: Front of Faceplate to Centerline of Top Venting Flue ........... 10"
|
|
| * All DXV-35 faces except the Andover, Bentley and Prairie have a 2" border around the faceplate. Non- combustible facing (brick, tile, etc.) may be applied to cover this border if desired. | * The Andover, Bentley and Prairie faces cover the 2" border. Non- combustible facing (brick, tile, etc.) may be applied onto this face to the edge of the doors, giving the Andover & Bentley a true arched fireplace appearance.. |
DIAGRAM #3: CORNER INSTALLATIONS (TOP VIEW)
R: Width of Cross-Corner Front Wall Framing if Top Vented............................... 52 17/32"
R(1): Width of Cross-Corner Front Wall Framing if Rear Vented........................... 64-5/32"
S: Finished Rear Wall to Front of Cross-Corner Wall Framing if Top Vented............ 37 1/8"
S(1) Finished Rear Wall to Front of Cross-Corner Wall Framing if Rear Vented... 44-29/32"
VENTING:
Rear Vent Configuration: 5" ID x 8" OD Coaxial Venting Pipe
Top Vent Configuration: 4" ID x 6-5/8" OD "Coaxial Venting Pipe
GAS PLUMBING:
The gas inlet access hole is located in the right sidewall as you face the viewing window: centerline of the 3/8" M.P.T. gasline connection is 7 3/16" back from the
front panel and 1 5/8" above the floor.
ELECTRICAL
Electrical wiring (115 Volts) feeds through the left side panel near the floor. Wiring connects to a duplex outlet inside the convection chamber under the firebox.
INSTALLING THE GAS LOG SET
For step-by-step instructions, click here.
(our reply form)
