FLAT WALL INSTALLATIONS: 

    CORNER INSTALLATIONS: 

A: STOVE TO BACKWALL:
   SINGLE-WALL STOVEPIPE........ 9"
   DOUBLE-WALL STOVEPIPE........ 6"
   MOBILE HOME.................. 7" 

G: STOVE TO CORNER WALLS:
   SINGLE-WALL STOVEPIPE....... 4"
   DOUBLE-WALL STOVEPIPE....... 4"
   MOBILE HOME................. 5" 

B: STOVE TO SIDEWALL:
   SINGLE-WALL STOVEPIPE....... 12"
   DOUBLE-WALL STOVEPIPE....... 12"
   MOBILE HOME................. 14" 

H: CENTERLINE PIPE TO CORNER WALLS:
   SINGLE-WALL STOVEPIPE.. 18-3/4"
   DOUBLE-WALL STOVEPIPE.. 18-3/4"
   MOBILE HOME............ 19-3/4" 

C: CENTERLINE PIPE TO BACKWALL:
   SINGLE-WALL STOVEPIPE... 17-1/2"
   DOUBLE-WALL STOVEPIPE... 14-1/2"
   MOBILE HOME............. 15-1/2" 

I: DIAGONAL FROM CORNER TO FRONT LOP:
   SINGLE-WALL STOVEPIPE...... 59"
   DOUBLE-WALL STOVEPIPE...... 59"
   MOBILE HOME................ 61" 

D: CENTERLINE PIPE TO SIDEWALL:
   SINGLE-WALL STOVEPIPE... 24-3/4"
   DOUBLE-WALL STOVEPIPE... 24-3/4"
   MOBILE HOME............. 26-3/4" 

J: CORNER TO EDGE OF HEARTH:
   SINGLE-WALL STOVEPIPE...... 56"
   DOUBLE-WALL STOVEPIPE...... 56"
   MOBILE HOME................ 57" 

E: MINIMUM HEARTH WIDTH........ 38" 

L: WIDTH OF FRONT LOP..... 37-1/2" 

F: BACKWALL TO FRONT OF HEARTH:
   SINGLE-WALL STOVEPIPE....... 52"
   DOUBLE-WALL STOVEPIPE....... 49"
   MOBILE HOME................. 50" 

COMBUSTIBLE ALCOVE DIMENSIONS:  
MINIMUM 55-1/2" Wide
MINIMUM 84" Tall
MAXIMUM 48" Deep 

OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACE

Install a length of 4" rigid or flexible aluminum intake pipe down through a 4-1/8" hole in the floor anywhere under the pedestal, extending below the floor joists and insulation. The intake pipe doesn't attach directly to the stove: snip and flare the pipe at the top to hold it in place. Use silicone cement to glue a piece of 1/4" wire rodent mesh at the bottom.

OUTSIDE AIR SUPPLIED THROUGH BACKWALL

Remove the air intake cover from the back of the pedestal and insert a length of 4" rigid or flexible aluminum intake pipe extending through 4-1/8" hole in outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place.

OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACE

Insert a length of 4" rigid or flexible aluminum intake pipe into the knockout hole in the bottom of the air plenum and extend it down through a 4-1/8" hole in the floor, terminating below the floor joists and insulation. Caulk around the intake pipe where it penetrates the floor and use silicone cement to glue a piece of 1/4" wire rodent mesh to the bottom.

OUTSIDE AIR SUPPLIED THROUGH BACKWALL

Insert a length of 4" rigid or flexible aluminum into the knockout hole in the rear of the air plenum and run back through a 4-1/8" hole in the outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place.