FLAT WALL INSTALLATIONS: 

    CORNER INSTALLATIONS: 

A: STOVE TO BACKWALL:
   SINGLE-WALL STOVEPIPE.... 13.5"
   DOUBLE-WALL STOVEPIPE..... 6.5"
   MOBILE HOME............... 9.5"
   ALCOVE................... 11.5" 

G: STOVE TO CORNER WALLS:
   SINGLE-WALL STOVEPIPE... 12"
   DOUBLE-WALL STOVEPIPE.... 5"
   MOBILE HOME.............. 9" 

B: STOVE TO SIDEWALL:
   SINGLE-WALL STOVEPIPE.... 18"
   DOUBLE-WALL STOVEPIPE.... 14"
   MOBILE HOME.............. 16"
   ALCOVE................... 16" 

H: CENTERLINE PIPE TO CORNER WALLS:
   SINGLE-WALL STOVEPIPE... 25"
   DOUBLE-WALL STOVEPIPE... 18"
   MOBILE HOME............. 22" 

C: CENTERLINE PIPE TO BACKWALL:
   SINGLE-WALL STOVEPIPE.... 22"
   DOUBLE-WALL STOVEPIPE.... 15"
   MOBILE HOME.............. 18"
   ALCOVE................... 20" 

I: DIAGONAL FROM CORNER TO FRONT LOP:
   SINGLE-WALL STOVEPIPE... 67"
   DOUBLE-WALL STOVEPIPE... 57"
   MOBILE HOME............. 63" 

D: CENTERLINE PIPE TO SIDEWALL:
   SINGLE-WALL STOVEPIPE.... 30"
   DOUBLE-WALL STOVEPIPE.... 26"
   MOBILE HOME.............. 28"
   ALCOVE................... 28" 

J: CORNER TO EDGE OF HEARTH:
   SINGLE-WALL STOVEPIPE... 60"
   DOUBLE-WALL STOVEPIPE... 53"
   MOBILE HOME............. 57" 

E: MINIMUM HEARTH WIDTH..... 34" 

L: WIDTH OF FRONT LOP...... 36" 

F: BACKWALL TO FRONT OF HEARTH:
   SINGLE-WALL STOVEPIPE... 54.5"
   DOUBLE-WALL STOVEPIPE... 47.5"
   MOBILE HOME............. 50.5"
   ALCOVE.................. 52.5" 

COMBUSTIBLE ALCOVE DIMENSIONS: 

MINIMUM 56" Wide
MINIMUM 90" Tall
MAXIMUM 48" Deep 

OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACE

Install a length of 4" rigid or flexible aluminum intake pipe down through a 4-1/8" hole in the floor anywhere under the pedestal, extending below the floor joists and insulation. The intake pipe doesn't attach directly to the stove: snip and flare the pipe at the top to hold it in place. Use silicone cement to glue a piece of 1/4" wire rodent mesh at the bottom.

OUTSIDE AIR SUPPLIED THROUGH BACKWALL

Remove the air intake cover from the back of the pedestal and insert a length of 4" rigid or flexible aluminum intake pipe extending through 4-1/8" hole in outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place.

OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACE

Insert a length of 4" rigid or flexible aluminum intake pipe into the knockout hole in the bottom of the air plenum and extend it down through a 4-1/8" hole in the floor, terminating below the floor joists and insulation. Caulk around the intake pipe where it penetrates the floor and use silicone cement to glue a piece of 1/4" wire rodent mesh to the bottom.

OUTSIDE AIR SUPPLIED THROUGH BACKWALL

Insert a length of 4" rigid or flexible aluminum into the knockout hole in the rear of the air plenum and run back through a 4-1/8" hole in the outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place.